- Steam Theory
- 1. Basics of Steam
- 2. Steam Control
- 3. Steam Heating
- 4. Basics of Steam Traps
- 5. Steam Trap Selection
- Steam Trap Selection: How Application Affects Selection
- Steam Trap Selection: Understanding Specifications
- Steam Trap Selection: Safety Factor and Life Cycle Cost
- Traps and Orifices Part 1
- Traps and Orifices Part 2
- Casting vs. Forging
- Applications of Different Types of Steam Traps
- Don't Get Steamed : Selecting Steam Trap Design
- Understanding Steam Traps
- Compare Two Fixed Orifice Venturi Products to a Variable Orifice Free Float Steam Trap
- 6. Steam Trap Problems
- 7. Steam Trap Management
- 8. Water Hammer
- Water Hammer: What is it?
- Water Hammer: The Mechanism
- Water Hammer: Cause and Location
- Water Hammer: In Steam Distribution Lines
- Water Hammer: In Equipment
- Water Hammer: In Condensate Transport Piping
- Identifying Water Hammer Using a Thermal Camera
- Mitigation of Water Hammer in Vertical Flashing Condensate Transport Piping
- Stop Knocking Your Condensate Return
- Steam Trap Management: Do Something; Anything. Please!
- 9. Risk Mitigation
- 10. Steam Quality
- 11. Steam Distribution
- 12. Condensate Recovery
- Introduction to Condensate Recovery
- Returning Condensate and When to Use Condensate Pumps
- Condensate Recovery: Vented vs. Pressurized Systems
- Condensate Recovery Piping
- What is Stall?
- Methods of Preventing Stall
- Cavitation in Condensate Pumps
- Steam Heat Exchangers are Underworked and Over-Surfaced
- Allocate New Plant Focus to Steam System Design—Part 2
- Optimize Reboiler Performance via Effective Condensate Drainage
- Vent Away Condensate Pump Frustrations in a Flash
- 13. Energy Efficiency
- Tips to improve steam plant efficiency
- Advice on Winter Preparation for Steam Systems
- Insulating Traps
- Steam Compressors
- Why Save Energy?
- Management Strategies for Conserving Energy
- Recovering Steam Clouds and Waste Heat
- Waste Heat Recovery
- Boiler Energy Saving Tips
- Steam Line Energy Saving Tips
- Steam-Using Equipment Energy Saving Tips
- Preventing Steam Leaks
- Handle Steam More Intelligently
- Optimize the Entire Steam System
- Use Available Data to Lower System Cost
- 14. Compressed Air / Gas
- 15. Other Valves
Temperature Control Trap Precautions
There is a kind of trap with the rather strange name of 'Temperature Control Trap.'
The main feature of the temperature control trap is that it can set the condensate temperature discharged.* By causing the condensate to pool in front of the trap, it becomes possible to discharge the condensate at a much lower temperature than the original steam, for example at 60 °C or 80 °C.
* Temperature of the condensate accumulating in the equipment or pipe and the product temperature cannot be set.
What is the Purpose of a Temperature Control Trap?
But aren't steam traps supposed to rapidly discharge any condensate that forms?' you may ask. An understanding of the reason for the development of the temperature control trap should help clear up any confusion about this.
The temperature control trap was developed for use with tracer lines that are designed to prevent high viscosity fluids such as heavy oil from cooling during transport, as cooling causes solidification of high viscosity fluids.
Heat from steam is used to maintain the temperature of heavy oil. A temperature of approximately 40 °C is sufficient to secure the transport of heavy oil, but the temperature of steam is over 100 °C. Therefore, if the heat of steam was used directly as the heat source, there would be a danger of overheating the heavy oil. Reducing the temperature of a tracer line by means of a temperature control trap prevents the possibility of overheating the heavy oil.
Can a Temperature Control Trap be Used as a Substitute for a Temperature Control Valve?
When steam is used for heating, control valves and temperature control valves are often used. May the temperature control trap be used in place of these control valves?
There is a crucial difference between the kind of temperature control provided by a control valve or a temperature control valve and that provided by a temperature control trap. Control valves and temperature control valves use the product temperature as their reference, while temperature control traps reference the temperature of the trap interior. Therefore, a temperature control trap cannot be used as a substitute for a control valve or temperature control valve in a typical heating situation.
Precautions for Use
In addition to use on tracer applications for high viscosity fluids such as heavy oil, temperature control traps are also used on tracer applications to prevent the freezing of instrumentation. Tracer applications are not widely used, however, so temperature control traps are a specialized trap with a limited application.
A temperature control trap deliberately pools condensate in order to prevent the overheating of the substance being heated.
Improve the flow properties of high viscosity fluids
Prevent Freezing of Instrumentation
Other than certain trace applications, there is essentially no application in which it is desirable to have condensate pool. Condensate is the arch enemy of the steam main line. At TLV, we make the following clear distinction:
- Use of temperature control traps is possible in some applications that make use of sensible heat (temperature control traps are not recommended for some applications which use sensible heat, contact TLV if you are unsure about a specific application using sensible heat).
- Use of temperature control traps is not possible in applications that make use of latent heat.
|Is My Trap Leaking Live Steam?||Trap Installation Orientation|