- Steam Theory
- 1. Basics of Steam
- 2. Steam Heating
- 3. Basics of Steam Traps
- 4. Steam Trap Selection
- Steam Trap Selection: How Application Affects Selection
- Steam Trap Selection: Understanding Specifications
- Steam Trap Selection: Safety Factor and Life Cycle Cost
- Traps and Orifices Part 1
- Traps and Orifices Part 2
- Casting vs. Forging
- Applications of Different Types of Steam Traps
- Don't Get Steamed : Selecting Steam Trap Design
- Understanding Steam Traps
- Compare Two Fixed Orifice Venturi Products to a Variable Orifice Free Float Steam Trap
- 5. Steam Trap Problems
- 6. Steam Trap Management
- 7. Water Hammer
- Water Hammer: What is it?
- Water Hammer: The Mechanism
- Water Hammer: Cause and Location
- Water Hammer: In Steam Distribution Lines
- Water Hammer: In Equipment
- Water Hammer: In Condensate Transport Piping
- Identifying Water Hammer Using a Thermal Camera
- Mitigation of Water Hammer in Vertical Flashing Condensate Transport Piping
- Stop Knocking Your Condensate Return
- Steam Trap Management: Do Something; Anything. Please!
- 8. Risk Mitigation
- 9. Steam Quality
- 10. Steam Distribution
- 11. Condensate Recovery
- Introduction to Condensate Recovery
- Returning Condensate and When to Use Condensate Pumps
- Condensate Recovery: Vented vs. Pressurized Systems
- Condensate Recovery Piping
- What is Stall?
- Methods of Preventing Stall
- Cavitation in Condensate Pumps
- Steam Heat Exchangers are Underworked and Over-Surfaced
- Allocate New Plant Focus to Steam System Design—Part 2
- Optimize Reboiler Performance via Effective Condensate Drainage
- 12. Energy Efficiency
- Tips to improve steam plant efficiency
- Advice on Winter Preparation for Steam Systems
- Insulating Traps
- Steam Compressors
- Why Save Energy?
- Management Strategies for Conserving Energy
- Recovering Steam Clouds and Waste Heat
- Waste Heat Recovery
- Boiler Energy Saving Tips
- Steam Line Energy Saving Tips
- Steam-Using Equipment Energy Saving Tips
- Preventing Steam Leaks
- Handle Steam More Intelligently
- Optimize the Entire Steam System
- Use Available Data to Lower System Cost
- 13. Compressed Air / Gas
- 14. Other Valves
Advice on Winter Preparation for Steam Systems
TLV Euro Engineering (Cheltenham, UK) - 2011/01/21
Michael Povey from TLV Euro Engineering looks at the consequences of frozen pipes and pipeline components, and what companies can do to prevent them.
Season follows season and then, towards the end of the year (surprise, surprise) winter arrives. Sometimes it is a mild one, sometimes harsh, but inevitably there will be a cold snap that takes temperatures down below freezing, and takes a lot of companies by surprise.
Companies that are prepared for winter should not have a problem, but problems await those that aren't.
In particular, steam systems and winter weather have a love/hate relationship that is easily spotted on any cold, clear winter's day in the form of condensation from every fugitive steam emission, small or large. Small visible emissions can actually be a real advantage for planned maintenance, as small leaks can be scheduled for repair in the next outage, hopefully at a much more sensible time and in a warmer month that avoids winter at all costs.
However, larger emissions inevitably present larger problems, as winter and incorrectly operating steam systems do not mix. Heat release from un-insulated or poorly insulated pipe-work can cost huge amounts of money and significantly increase CO2 emissions. In winter, with a long enough un-insulated pipe, the steam/resulting condensate from it can freeze. It should also be noted that ambient and wind-chill temperatures are not the only problems - penetration of the insulation by rain or snow will also accelerate the cooling process, and sub-zero temperatures can even freeze previously hot pipe-work.
As well as the cooling effect of the weather there are other factors to consider in winter, including those that can cause the slowing of condensate flow. For example, a condensate strainer that is blocking will slow the flow of condensate through the pipe and trap, making a freeze-up more likely. Pipe-work and flanges exposed to heavy wind, rain and snow are more likely to freeze, and pipes lose heat and are more likely to freeze if they are bracketed directly to large steel surfaces such as pipe bridges and A-frames.
After considering these points, some may still ask what the consequences of freezing are and whether it is such a big problem if pipe-work freezes. After all, a frozen pipe will eventually defrost.
However, in the mean time, ice now occupies the whole of the pipe in which once it was a flowing liquid. As the temperature increases after the freezing incident, the volume of the ice increases per unit of mass - in other words, it gets bigger. Expanding ice does not respect the boundaries in which it is contained and will continue to expand until it turns back to water when the pressure equalises throughout the system, exerting huge hydraulic forces on pipes and pipeline components. These items are commonly pressure rated to PN16-PN40 and, as such, will probably be hydraulically tested to twice the service pressure. However, the forces within iced pipelines will be much greater than the design pressure and more than the hydraulic test of pipeline components, so something's got to give and it will usually be the weakest link in the chain - a pipeline component.
If this happens when steam pressure is off, catastrophe may be averted and there may simply be a leak when the system starts to pressurise. A much more serious problem, or even a catastrophe, may result if the system is at full pressure and a component fails. At this stage there will be an unexpected and sudden release of pressurised hot water and steam leading to very much more serious consequences to plant and possibly personnel.
There are several pre-winter checks companies can make to help prevent freezing.
- Ensure insulation is adequately waterproofed and covers the whole system. Where certain designs of steam traps cannot be insulated, contact the manufacturer for advice.
- Insulate pipes from the steel work to which it is bolted.
- Survey pipes and pipeline components, ensuring that strainers/traps are clean, blockage-free and operating correctly.
- If freeze-ups are common, ask a steam specialist or component manufacturer to advise on the design of the system and assist with layouts and designs of condensate return pipe-work.
- Install anti-freeze valves (in low points where possible) and trap bodies into which cold condensate can drain before freezing occurs.
- Run pipes inside a building if possible - if not, build a duct or a cover to keep the weather off the cladding surface.
In short, be prepared and do not get caught out this winter.
If in doubt, seek advice from a steam specialist or talk to your component manufacturer.
|Tips to improve steam plant efficiency||Insulating Traps|